Flintec DAD 141.1 Instrukcja Użytkownika

Load Cell Digitizing Unit Type DAD 141.1 Communication via RS 422/485 & Ethernet

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 10 of 54 5. Hardware and Wiring 5.1. Housing & Terminals 5.2.

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 11 of 54 5.4. Terminals Power Supply Depending on the grounding concept of

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 12 of 54 Traceable Access Code (TAC) protected calibration commands In case the seal switch

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 13 of 54 6. Menu Structure Setup Keybord

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 14 of 54 7. Setup Via Front Panel Keyboard 7.1. Keyboard Buttons This is the ZERO butt

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 15 of 54 7.3. Menu 1 – System Zero Remark: Activate a new calibration with 1x Power OFF/ON

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 16 of 54 7.4. Menu 2 – System Span Remark: Activate a new calibration with 1x Power OFF/ON

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 17 of 54 7.6. Menu 4 – Filter & Motion Detection 4 Digital filter & No Motio

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 18 of 54 7.7. Menu 5 – Analog Output 5 Analog output setup (Menu 5.1 to 5.5)

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 19 of 54 7.8. Menu 6 – Logic Inputs 6 Logic input setup (Menu 6.0 to 6.1)

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 2 of 54 0. Table of Contents: 0. Table of Contents: ...

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 20 of 54 7.9. Menu 7 – Logic Outputs 7 Logic output setup (Menu 7.0 to 7.2)

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 21 of 54 7.10. Menu 8 – Data Communication 8 Data Communication setup (Menu 8.1 to 8.

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 22 of 54 Menu 8 – Data Communication / Continuation 8 Data Communication setup (Menu 8

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 23 of 54 7.11. Error Codes

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 24 of 54 8. Examples 8.1. Example 1 – Calibration procedure using weights 3 Leg tank or

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 25 of 54 g The last point for this example are the settings of over/under range. Go

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 26 of 54 8.2. Example 2 – Calibration procedure using load cell’s mV/V

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 27 of 54 f Go to Menu 2.3. by using the UP/DOWN and ZERO keys. The display shows 00.000m

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 28 of 54 9. Commands – Overview Command Short description Parameter value Page AA Get

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 29 of 54 Command Short description Parameter value Page OM Output Mask – to control hy

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 3 of 54 9. Commands – Overview ...

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 30 of 54 10. Commands Description For better clarity, all commands are divided into group

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 31 of 54 10.1.5. SR Reset DAD 141.1 Firmware Master (PC / SPS) sends Slave (DAD 141.1) re

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 32 of 54 10.2.4. DS Set Display Step Size [ Index 0x2216 ] This command allows the

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 33 of 54 10.2.8. ZT Zero Tracking [ Index 0x2122 ] This command enables / disabl

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 34 of 54 10.2.12. AZ Absolute zero point calibration (eCal) [ Index 0x2202 ] The comma

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 35 of 54 10.3. Motion Detection Commands – NR, NT The motion detection facility provides

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 36 of 54 10.4. Filter Setting Commands – FM, FL, UR A digital filter can be set which will

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 37 of 54 Mode 1 (FIR filter) Settings / Characteristic FL Settling time to 0.1% (ms) 3 dB

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 38 of 54 10.5. Taring and Zeroing Commands – SZ, RZ, ZN, ST, RT, TN, RW, TI The following

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 39 of 54 10.5.6. TN Store Tare Value [ Index 0x2224 ] This command allows to

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 4 of 54 10.7. Auto-Transmit Commands – SG, SN, SW, SA, SH, SM, SO, SV ...

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 40 of 54 10.6. Output Commands – GG, GN, ON, GT, GS, GW, GA, GH, GM, RM, GO, GV The follo

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 41 of 54 The checksum is derived as follows: a. Add the ASCII values (in hex) of all the

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 42 of 54 10.7. Auto-Transmit Commands – SG, SN, SW, SA, SH, SM, SO, SV The following comma

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 43 of 54 10.8. Logic Input Functions & Status – AI’n’, IN 10.8.1. AI Assign input

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 44 of 54 10.9. Logic Output Commands - IO, OM, S’n’, H’n’, P’n’, A’n’, HT The definiti

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 45 of 54 10.9.3. A’n’ Assign action for setpoint ‘n’ [ Index 0x2068 ] This command is

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 46 of 54 10.9.6. P’n’ Polarity of Setpoint [ Index 0x2070 ] This command is used to

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 47 of 54 10.10. Communication Setup Commands – AD, NA, BR, DX, OP, CL, TD 10.10.1. AD

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 48 of 54 10.11. Analog Output – AA, AH, AL, AM The following commands must be saved in E

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 49 of 54 10.12. Save Calibration and Setup – CS, WP, SS, AS, GI, PI The calibration and

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 5 of 54 RIGHTS AND LIABILITIES All rights reserved. No part of this publication may be re

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 50 of 54 10.13. Trigger Commands – SD, MT, GA, TE, TR, TL, SA Note: All changes to the t

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 51 of 54 10.13.6. TL Trigger Level [ Index 0x211E or 0x2400 ] This command d

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 52 of 54 11. Use in “Approved” Applications The term “approved” applies whenever the weigh

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 53 of 54 12. Calibration and Calibration Sequence The calibration of DAD 141.1 is only pos

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 54 of 54 13. Updates – Firmware Download For a firmware update the DAD 141.1 has to be con

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 6 of 54 2. Declaration of Conformity EG-Konformitätserklärung EC-Declaration of Confor

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 7 of 54 3. Introduction and Specifications The all-in-one Digital Amplifier DAD 141.1 is

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 8 of 54 4. Communications and Getting started 4.1. Serial Interface Communicating with t

DAD 141.1 Technical Manual, Rev. 2.2 - February 2014 Page 9 of 54 4.5. Getting Started Via Ethernet Interface You will require:  PC or PLC with a